SCU41 password protected
A customer of ours returned a CJ1W-SCU41 and ofcourse he password protected the protocole. i don't need to upload the protocol i just need to make this SCU41 operational again with my new protocol. but...
View ArticleOMRON PLC with Modbus TCP/IP
Hello Has anyone got an Omron PLC running with Modbus TCP/IP? If so was it difficult? I'm thinking of using this PLC as it has Ethernet/IP as well. http://www.ia.omron.com/products/family/3650/ Thanks!
View ArticleNB Designer V1.6
Hello, We purchase nb10-V1 need help a software v1.6.please.. Cant Access with 1.531 version. Thank you,
View ArticleSyswin & WinXP
Anyone been able to get Syswin to run under XP?? I cant get it to install all i get is file is not suitable for windows applications. Any ideas???
View ArticleOmron CJ2M HF Watchdog Error
Hello, We have a problem with a PLC Omron Cj2M-CPU31, previously worked fine for a long time, before it intermittently indicates an HF error during operation. In this case, I can't connect to PLC via...
View ArticleClik here to view.
Connect Omron CP1L to Maple HMI by CP1W-CIF01?
I am trying to get a Maple 5040B to communicate with an Omron CP1L-L14DR-A over an RS-232 serial connection using the option board CP1W-CIF01 that is plugged into the PLC. I have sent the program and...
View ArticleCQM1H Problem
Dear All CQM1H is installed with Remote unit SRT2-ROC08 and some other modules Problem we are facing is that some time, when we Power ON the machine then CQM1H error indication goes ON and RUN...
View ArticleConnect two CPU CJ2M
Hi there, I have a question for you all. Is it possible to create an ethernet connection between 2 CPU CJ2M through their onboard ethernet card? I would like to share some DM words between the 2 CPUs....
View ArticleHow to communicate NB10W-TW01B and S7-1500 using Ethernet
Dear All, Does anyone have experience to communicate NB10W-TW01B and S7-1500 using Ethernet? In NB-Designer (OMRON HMI Software), there is no selection for S7-1500, Any one can help me plz?
View ArticleDRT2-OD16 outputs are resetted after connection recovery
Hi everyone. My machine uses CIF50-DNM as DeviceNet master board, and many remote IO stations DRT2-OD16. I configure Output Hold for some outputs point of DRT2-OD16 so that when I turn off PC (turn...
View ArticleExplicit message of DRT2 remote IO series
Hi everyone. I want to turn on Output Hold mode of Remote IO station DRT2-OD16 via explicit message (because my master board is CIF50-DNM, so I can't use Network configurator to configure this). I am...
View ArticleClik here to view.
omron plc
Hi ! I have a question regarding the handling of the signal from the Tc101. I connected to PLC CQM1H and connected to my PLC. I downloaded a .pdf LINKED from "my omron", read it and put together a...
View ArticleE5EK-AA2-DRT Temperature Controller
We have an E5EK-AA2-DRT Temperature Controller that we needed to replace as it had an issue with its DeviceNet connection. We have a 2nd hand spare that was previously removed from another burner...
View ArticleClik here to view.
Omron PLC to PC through PROFIBUS
Hello, I need to connect a PC to an Omron CJ2M-CPU12 PLC and to be able to access any memory address, as you would do it over serial cable. As the RS232 port is set to NTLink for communication with...
View ArticleCJ2M-CPU35 HF Watchdog WDT Error
The CJ2M-CPU35 face a HF WDT Error. Power off and on for restart, it can work normally. Approximately once per day, with no consistent . We replaced the unit with another CJ2M-CPU35 (from the same...
View ArticleRemoving EIP nodes from network without errors
I have a new project for a semi-auto testing station. The station needs to be movable so it can be placed near another machine when in use. When not in use, then this test station needs to be moved...
View ArticleBarcode Scanner to NS10 to PLC
Hi all again, I'd never done this before using Omron hardware, so I don't know what's the requirement. I'm trying to setup a barcode scanner to send a string/number to NS10 and to send that data...
View ArticleCP1E-N40DR-A – Replacing Only the CPU from an Identical Faulty PLC
Hi everyone, I have an elevator system that uses a CP1E-N40DR-A. There is also a relay expansion module connected on the side. The PLC power supply failed. I had a technician extract the program and...
View ArticleC200H-LK201
Hi, i have a blow molding machine. somehow it just not responding. the omron NB screen says PLC comms error. the C200H-LK201 is the guy connected with the screen. i am not that expert but looks like...
View ArticleNX1P2 FTPPutFile Errors
Hi! I am using the Omron NX1P2 PLC to send log files from the SD card on my PLC to an FTP client on a PC connected via ethernet. However, I keep getting an error ID of 2406 and I am not sure why. I...
View ArticleNP Designer Software
Hi Guys! Hope you can help me with this one. I have an NP programmable terminal...my problem is the NP designer software being offered in Omron website does not communicate with the hardware. Before I...
View Article3GMX2 on Ethernet/IP F002 / F003
I'm new to these VSD's 3GMX2's, I have them communicating using ethernet/ip on the standard profile 4 Bytes in / 4 Bytes out. Should I be able to set parameters F002/F003 Accel/Decel time ? I have...
View ArticleAnalog Process Indication
Hello Guys...... Good Day I am working on a project for tank filling system. Suppose if the filling starts, then the filling indicator should be ON ( panel front) based on flowmeter connected to a...
View ArticleIntegrating Barcode Sensors with CP2E-N20DR-A
I'am just starting using omron CP series, and my plan is i wanna integrating 2 plc omron CP1E-N40 (with CP1W-CIF41 eternet port) and a CP2E-N20 for communication using ethernet an fins (PLC-PLC). In...
View ArticleClik here to view.
Need Help Sorting out a "PLC Responce error"
Hey so I Keep getting "PLC Response error" on the hmi I'm connecting a NB10W-TW01B hmi to a Omron Nx102-9020 Using ethernet 2. Using Sysmac Studio For the plc programming and NB-Designer for the HMI...
View Article